Upset Forging

1. Upset Forging

Upset forging increases the diameter of the workpiece by compressing its length. Based on number of pieces produced this is the most widely used forging process. A few examples of common parts produced using the upset forging process are engine valves, couplings, bolts, screws, and other fasteners. Upset forging is usually done in special high-speed machines called crank presses, but upsetting can also be done in a vertical crank press or a hydraulic press. The machines are usually set up to work in the horizontal plane, to facilitate the quick exchange of workpieces from one station to the next. The initial workpiece is usually wire or rod, but some machines can accept bars up to 25 cm (9.8 in) in diameter and a capacity of over 1000 tons. The standard upsetting machine employs split dies that contain multiple cavities. The dies open enough to allow the workpiece to move from one cavity to the next; the dies then close and the heading tool, or ram, then moves longitudinally against the bar, upsetting it into the cavity. If all of the cavities are utilized on every cycle then a finished part will be produced with every cycle, which makes this process advantageous for mass production.

http://www.kt-forge.co.uk/upset-forging

2. Stainless Steel High Pressure Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com

3. House For Rent Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4rent.co.uk/house-for-rent-huddersfield

4. Bulk Bearings

We purchase bearings and transmission products in bulk. If you would like to dispose of surplus or bankrupt stock, sell in bulk or just clear some of your inventory, we would like to hear from you.

http://www.surplus-bearings.co.uk

5. Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://1t-s.com/application-development

6. Student Accomodation in Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4share.co.uk/student-accomodation-huddersfield

7. Student Accomodation Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.student-housing-huddersfield.co.uk/

8. Stainless Steel Valves

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com/product-list/valves/7

9. Bankrupt Bearings

We purchase bearings and transmission products in bulk. If you would like to dispose of surplus or bankrupt stock, sell in bulk or just clear some of your inventory, we would like to hear from you.

http://www.surplus-bearings.co.uk

10. Weldolets

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com

11. South Yorkshire Linux

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://www.south-yorkshire.linux.1t-s.com

12. Steel Forging

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/steel-forging

13. Huddersfield Student Housing

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.student-housing-huddersfield.co.uk/

14. Huddersfield University Accomodation

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.student-housing-huddersfield.co.uk/

15. Sheffield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.sheffield.bespoke.software.abrt.com

16. Rotherham Open Source

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://www.rotherham.open-source.1t-s.com

17. SKF Bearings

Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland

http://www.steelcitybearings.com

18. Weldolets

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com/product-list/high-pressure-fittings/4?&Fitting=Weldolet

19. Ball Bearings

Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland

http://www.steelcitybearings.com

20. Swaging

T=Swaging is a forging process in which the dimensions of an item are altered using a die or dies, into which the item is forced. Swaging is usually a cold working process; however, it is sometimes done as a hot working process. Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/swaging

21. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.bespoke.software.1t-s.com

22. Sheffield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.application-development.1tsolutions.com

23. Ball Bearings

Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland

http://www.steelcitybearings.com

24. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.custom.software.1t-s.com

25. Self Lube Bearings

A self-lubricating bearing, often referred to as a "self-lube bearing," is a type of bearing designed to operate without the need for external lubrication, such as grease or oil. These bearings are used in various applications where traditional lubrication methods may be impractical or where maintenance requirements need to be minimized. Self-lubricating bearings typically incorporate a solid lubricant within the bearing material or have special reservoirs or channels designed to release lubrication as needed during operation. The primary advantage of self-lubricating bearings is their ability to reduce friction and wear over time without the need for manual lubrication or maintenance.

https://www.bearingswebshop.com/product-category/self-lube-bearings/

26. Computer Repair

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://abrt.com/computer-repair

27. Waste Management Software

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://waste-management-software.skip-manager.com

28. Sheffield Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.software.devlopment.1t-s.com

29. Stainless Steel Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com

30. Chesterfield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.custom-software.1tsolutions.com

31. Waste Recycling System

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://waste-recycling-system.skip-manager.co.uk

32. Swaging

T=Swaging is a forging process in which the dimensions of an item are altered using a die or dies, into which the item is forced. Swaging is usually a cold working process; however, it is sometimes done as a hot working process. Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.kt-forge.co.uk/swaging

33. Rotherham Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://rotherham.bespoke.software.abrt.com

34. Ice Ledger, Become a Partner and promote yourself and your organisation.

Ice Ledger is a comprehensive business accounting software for small to medium sized business that you can download for free and start using immediately. The system is FREE to use for a whole year. Accounting features include sales ledger, sales quotes, sales order processing, sales invoicing, purchase ledger, purchase enquiries, purchase order processing, purchase invoicing, nominal ledger, stock control, Intrastat reporting, multi-currency and much more ...

http://www.iceledger.com/partners

35. Bearings

Steel City Bearings are one of the worlds leading suppliers of all bearing and transmission products. Steel City Bearings Ltd can offer the following to all its customers: Massive stocks of all leading brands * Same day despatch on ALL stock items * Over 100 years of bearing and transmission knowledge * Highly competitive pricing * Friendly and reliable sales team * Over 25,000 lines and 250,000 items in stock * Next day delivery to mainland UK including Northern Ireland

http://www.steelcitybearings.com

36. House For Rent Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://house-for-rent-huddersfield.iam4rent.co.uk/

37. 316 Stainless Steel

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com

38. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.1tsolutions.com/custom-software

39. Rotherham Open Source

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://rotherham.open-source.1t-s.com

40. South Yorkshire Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.bespoke.software.abrt.com

41. Student Accomodation in Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4share.co.uk/student-accomodation-huddersfield

42. South Yorkshire Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.custom-software.1tsolutions.com

43. Forging Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://forging-steel.ktforge.co.uk

44. Drop Forging

Drop forging is a metal shaping process, the metal to be formed is first heated then shaped by forcing it into the contours of a die, this force can be in excess of 2000 tons. The drop forging process can be performed with the material at various temperatures. Hot Forging: During hot forging the metals are heated to above their recrystallization temperature. The main benefit of this hot forging is that work hardening is prevented due to the recrystallization of the metal as it begins to cool. Cold Forging: Cold Forging is generally performed with metal at room temperature below the the recrystallization temperature. Cold forging typically work hardens the metal. There are two types of drop forging, open die and closed die. Open die drop forging requires the operator to position the work piece while it is impacted by the ram. The die attached to the ram is usually flat or of a simple contour, most of the shaping is achieved by the operator physically positioning the work piece before each stroke of the ram. There are also special dies which can be used to cut the metal, form holes or notches.

http://drop-forging.kt-forge.co.uk

45. Roller Bearings

A roller bearing is a type of rolling-element bearing that is designed to reduce friction between moving parts in various machinery and mechanical systems. It consists of two main components: an inner ring and an outer ring, with a set of cylindrical or tapered rollers placed between them. These rollers allow for smooth and low-friction rotation of the inner and outer rings relative to each other. The primary purpose of a roller bearing is to support axial and radial loads while minimizing friction and wear. The rolling motion of the cylindrical or tapered rollers reduces the sliding friction that would occur if two surfaces were in direct contact. This design helps improve the efficiency and lifespan of the machinery or equipment where roller bearings are used.

https://www.bearingswebshop.com/product-category/roller-bearings/

46. IT Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.1t-s.com/service

47. Barnsley Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://barnsley.custom.software.abrt.com

48. High Pressure Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com/product-list/high-pressure-fittings/4

49. Chesterfield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.custom.software.abrt.com

50. Chesterfield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.chesterfield.custom.software.abrt.com

51. Barnsley Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.bespoke.software.1t-s.com

52. Swaging

T=Swaging is a forging process in which the dimensions of an item are altered using a die or dies, into which the item is forced. Swaging is usually a cold working process; however, it is sometimes done as a hot working process. Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://swaging.ktforge.co.uk

53. Doncaster Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.doncaster.computer.service.1t-s.com

54. Rotherham Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.rotherham.bespoke.software.abrt.com

55. Press Forging

Press forging works by slowly applying a continuous pressure or force, which differs from the near-instantaneous impact of drop-hammer forging. The amount of time the dies are in contact with the workpiece is measured in seconds (as compared to the milliseconds of drop-hammer forges). The press forging operation can be done either cold or hot. The main advantage of press forging, as compared to drop-hammer forging, is its ability to deform the complete workpiece. Drop-hammer forging usually only deforms the surfaces of the workpiece in contact with the hammer and anvil; the interior of the workpiece will stay relatively undeformed. Another advantage to the process includes the knowledge of the new part's strain rate. We specifically know what kind of strain can be put on the part, because the compression rate of the press forging operation is controlled.

http://press-forging.ktforge.co.uk

56. Open Die Forging

Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.

http://open-die-forging.kt-forge.co.uk

57. Msajid Prayer Times

Masjid Prayer Times, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Jamat Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.

http://masjid-prayer-times.jamat-times.com

58. South Yorkshire Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.custom.software.abrt.com

59. Rotherham Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://rotherham.software.development.1tsolutions.com

60. Hot Forging

Hot forging is the plastic deformation of metal at a temperature and strain rate such that recrystallization occurs simultaneously with deformation, thus avoiding strain hardening. For this to occur, high workpiece temperature (matching the metal's recrystallization temperature) must be attained throughout the process. A form of hot forging is isothermal forging, where materials and dies are heated to the same temperature. In nearly all cases, isothermal forging is conducted on superalloys in a vacuum or highly controlled atmosphere to prevent oxidation.

http://www.kt-forge.co.uk/hot-forging

61. Open Die Forging

Open-die forging is also known as smith forging. In open-die forging, a hammer strikes and deforms the workpiece, which is placed on a stationary anvil. Open-die forging gets its name from the fact that the dies (the surfaces that are in contact with the workpiece) do not enclose the workpiece, allowing it to flow except where contacted by the dies. Therefore the operator needs to orient and position the workpiece to get the desired shape. The dies are usually flat in shape, but some have a specially shaped surface for specialized operations. For example, a die may have a round, concave, or convex surface or be a tool to form holes or be a cut-off tool. Open-die forging lends itself to short runs and is appropriate for art smithing and custom work. In some cases, open-die forging may be employed to rough-shape ingots to prepare them for subsequent operations. Open-die forging may also orient the grain to increase strength in the required direction. Cogging is successive deformation of a bar along its length using an open-die drop forge. It is commonly used to work a piece of raw material to the proper thickness.

http://www.ktforge.co.uk/open-die-forging

62. IT Support

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.1t-s.com/service

63. Press Forging

Press forging works by slowly applying a continuous pressure or force, which differs from the near-instantaneous impact of drop-hammer forging. The amount of time the dies are in contact with the workpiece is measured in seconds (as compared to the milliseconds of drop-hammer forges). The press forging operation can be done either cold or hot. The main advantage of press forging, as compared to drop-hammer forging, is its ability to deform the complete workpiece. Drop-hammer forging usually only deforms the surfaces of the workpiece in contact with the hammer and anvil; the interior of the workpiece will stay relatively undeformed. Another advantage to the process includes the knowledge of the new part's strain rate. We specifically know what kind of strain can be put on the part, because the compression rate of the press forging operation is controlled.

http://press-forging.kt-forge.co.uk

64. South Yorkshire eCommerce

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://www.1t-s.com/internet-web-design

65. Student Accomodation in Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://student-accomodation-huddersfield.iam4rent.co.uk/

66. South Yorkshire Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://www.south-yorkshire.web-design.1t-s.com

67. Student Accomodation in Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4rent.co.uk/student-accomodation-huddersfield

68. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.bespoke-software.1tsolutions.com

69. Stainless Steel Forging

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/stainless-steel-forging

70. Low Pressure BSP Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com/product-list/low-pressure-fittings/3

71. House For Rent Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.iam4share.co.uk/house-for-rent-huddersfield

72. Cold Forming

Cold forging is a high speed manufacturing process whereby metal is shaped at room temperature often without the need for the removal of material. A simple blank is placed within a die and a punch is pressed into the blank. The blank then takes on the form of the punch and the die. By utilising multiple dies and punches in succession very complex shapes can be achieved. Metal is forced beyond its yield (elastic) limit and retains its altered shape upon removal from the die. The metal is not forced beyond its tensile strength, otherwise fracturing would occur (the exception is when trimming or piercing). Historically cold forming has been an experienced based technology, but this is changing as new computer based analytical tools are constantly being developed.

http://cold-forming.kt-forge.co.uk

73. Stainless Steel Flanges

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com

74. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.1t-s.com/bespoke-software

75. Chesterfield Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://chesterfield.software.devlopment.1t-s.com

76. Software Development

Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.1tsolutions.com/software-development

77. Doncaster Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.doncaster.application.development.1t-s.com

78. Rotherham Linux

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://rotherham.linux.1t-s.com

79. Waste Management Software

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://www.waste-management-software.skip-manager.co.uk

80. Tapered Bearings

A tapered roller bearing, commonly referred to as a "tapered bearing," is a type of rolling-element bearing designed to handle both radial and axial (thrust) loads. These bearings are named for their conical (tapered) shape, where the inner and outer races (rings) and the rollers are shaped like truncated cones. Tapered roller bearings are widely used in various applications, including automotive, industrial machinery, and heavy equipment.

https://www.bearingswebshop.com/product-category/tapered-bearings/

81. Doncaster Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://doncaster.application.development.1t-s.com

82. Rotherham Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.rotherham.bespoke.software.1t-s.com

83. Forging Stainless Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://forging-stainless-steel.ktforge.co.uk

84. Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://bespoke.software.1t-s.com

85. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://custom.software.1t-s.com

86. South Yorkshire Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://south-yorkshire.software.devlopment.1t-s.com

87. Software Development

Software development services, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://1tsolutions.com/software-development

88. Salaat Times

Salaat Times, Salah Times, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Jamat Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.

http://salaat-times.jamat-times.com

89. Skip Manager

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://skip-manager.com

90. Stainless Steel Low Pressure Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com/product-list/low-pressure-fittings/3

91. South Yorkshire Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.south-yorkshire.software.development.1tsolutions.com

92. Barnsley Web Design

Professional and creative web design services. We build web sites for businesses across South Yorkshire, Rotherham, Sheffield, Doncaster and Barnsley. From a simple brochure to e-commerce with advanced dynamic content features, we can build the web site t promote your business on-line.

http://barnsley.web-design.1t-s.com

93. Forging Steel

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://www.ktforge.co.uk/forging-steel

94. Doncaster Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://doncaster.custom.software.1t-s.com

95. Barnsley Open Source

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://barnsley.open-source.1t-s.com

96. Jamat Times

Jamat Times, Clock, Islamic calendar and message display board software program for PCs designed specially for Masjids and Mosques. Suitable for Salah Times, Salah Timetable, Namaz Times, Salaat Times. Free Download.

http://www.jamat-times.com

97. House to Share Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://house-to-share-huddersfield.iam4share.co.uk/

98. Doncaster Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.doncaster.software.development.abrt.com

99. Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://grid-itc.com/computer-services

100. Waste Recycling Software

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://waste-recycling-software.skip-manager.com

101. Chesterfield Linux

1T Solutions install and support linux based open source solutions and systems to small and medium businesses across Rotherham, Sheffield, Barnsley, Doncaster, Chesterfield and across South Yorkshire.

http://chesterfield.linux.1t-s.com

102. Spam Filter

A spam filtering service suitable for small and medium businesses, the 1T Solutions Gatekeeper service is competitively priced, and removes over 95% of e-mail spam and viruses.

http://www.1t-s.com/spam-filter

103. Computer Maintenance

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.grid-itc.com/computer-maintenance

104. Doncaster Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://doncaster.software.devlopment.1t-s.com

105. Steel Forging

Virtually all metals that can be moulded / drawn out may be forged by first heating and then hammering it in to the desired shape. A billet, wrought bar, cast or sintered ingot etc.. may be forged. Forging improves the toughness and strength of improving orientation of the metal grain structure. The repeated heating and hammering causes the metal to become more dense and the grain "flow lines" to follow the contour of the end product.

http://steel-forging.ktforge.co.uk

106. Low Pressure BSP Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com/product-list/low-pressure-fittings/3

107. Stainless Steel Pipes

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com

108. Sheffield Application Development

Computer applications software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.application.development.1t-s.com

109. Computer Services

Computer service and support across Rotherham, Sheffield, Doncaster and Barnsley. 1T Solutions Ltd offer cost effective computer maintenance for small and medium businesses.

http://www.abrt.com/computer-services

110. Stainless Steel Low Pressure BSP Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com/product-list/low-pressure-fittings/3

111. Smith Forging

Forging worked between flat or simple contour dies by repeated strokes and manipulation of the workpiece. Also known as "hand" or "flat die " forging.Heavy workpieces could be processed using a smith-forging hammer, and smaller forgings are die formed in drop hammers. Smith forging hammers are typically steam or air-operated, consisting of a power actuated ram supported by a heavy cast iron frame. The final product is a result of the ram being powered into the dies containing the workpiece.

http://www.ktforge.co.uk/smith-forging

112. Barnsley Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.barnsley.software.development.abrt.com

113. Doncaster Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://doncaster.custom.software.abrt.com

114. Chesterfield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.chesterfield.custom-software.1tsolutions.com

115. Sheffield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.bespoke.software.1t-s.com

116. Barnsley Software Development

Software Development, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://barnsley.software.devlopment.1t-s.com

117. Skip Hire System

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://www.skip-hire-software.skip-manager.com

118. Gatekeeper

A spam filtering service suitable for small and medium businesses, the 1T Solutions Gatekeeper service is competitively priced, and removes over 95% of e-mail spam and viruses.

http://www.1t-s.com/gatekeeper

119. Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.1t-s.com/custom-software

120. Butt-Weld Fittings

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com

121. Waste Recycling System

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.

http://www.waste-recycling-system.skip-manager.co.uk

122. Stainless Steel

ZX55.com are on-line suppliers of stainless steel products including Butt-Weld Fittings, Flanges, Gaskets, High Pressure Fittings, Hygenic Fittings, Low Pressure Fittings, Pipes and Valves.

https://www.zx55.com

123. Sheffield Bespoke Software

Bespoke software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://www.sheffield.bespoke.software.1t-s.com

124. Sheffield Custom Software

Custom software, tailored to your business practices. 1T Solutions have been delivering bespoke integrated systems since our inception in 2001. The underlying philosophy with all our bespoke software projects is to wrap the software around our clients' business. It is a very sad fact, even today, that many software houses develop applications where the client must change their business practices to suit the software - not so with 1T Solutions. From small businesses to corporate clients, across a wide industry spectrum, we have a wealth of expertise in designing and implementing diverse business solutions.

http://sheffield.custom.software.1t-s.com

125. House to Share Huddersfield

4 Bedroom house to share: Student accomodation available to rent near Huddersfield University. House with four bedrooms to let with common sitting-room, shared kitchen and batchroom with over the bath shower. Two of the rooms have on suite toilet and wash basin. The house is located in the Paddock area of Huddersfield, post code HD1 and is 1.4 miles from the University, 1.2 miles from the Huddersfield train station. The house is on a regular bus route, buses 301a, 302 (every 15 minutes) and 302a.

http://www.student-housing-huddersfield.co.uk/

126. Waste Collection Software

Skip Manager has been designed to enable you to manage the hire of your skips more effectively. From the initial bookings, hire, tracking and collections to credit control, Skip Manager has the functionality required for your Waste Recycling business.